The CADDY Solar Cable Clip offers, in comparison to conventional cable clips and cable ties, even under extreme climatic conditions, a long-time, reliable and professional cable fastening to the module frame. Spezial features are:
The CADDY Armour corrosion protection system of the CADDY Solar cable clip was tested according to ISO 7253 with 720 hours of salt spray test and is classified in class C4 according to EN ISO 12944-6 (corrosion load strong, protection duration long – over 15 years).
nVent – WARNING:
nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.erico.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent ‘s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.
© 2020 nVent. All rights reserved
nVent, nVent CADDY, nVent ERICO, nVent ERIFLEX and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.
Please note in general:
-
The installation of our products should only be carried out by qualified and professional specialists with experience in installing on roofs. The suitability of our sold products for the intended use is checked by the user himself. If technical details are not described separately, this does not release the company carrying out the work from its obligation to check the individual case and clarify the correct technical facts beforehand.
-
The user and/or installer bears also the responsibility not only for the professional installation, but also for the roof on which he is mounted. The user and/or installer must always clarify in advance the application possibilities and application of our products in connection with the other used materials and products at the single project.
-
The material properties, the combination with each other as well as the installation instructions and regulations of all manufacturers involved (including those of the roof) must be observed.
-
It must be ensured by the planner and the specialist company responsible for the installation that the planning and installation are carried out strictly in accordance with the national and site-specific building regulations, occupational safety and accident prevention regulations, standards and environmental protection regulations. Every person who plans and installs with our products is obliged to inform himself independently about all rules and regulations for technically correct planning and installation and to observe them. This also includes obtaining the current status of the necessary rules and regulations.
-
The user and/or installer of all our products is responsible for all necessary engineering and design to ensure that the products has been properly spaced and configured. It is the responsibility of the user to verify this information, or seek assistance from a qualified design professional or stress analyst, if necessary. RoofTech GmbH and the makers make no representations with respect to these variables.
-
RoofTech GmbH and nVent/Erico recommend that the planned installation should be verified by a qualified professional who is responsible for the snow and wind loads, the additional loads from the installations attached to the Tool-Free supports, the statics and assembly as well as the planning and construction of and on roofs.
-
The respective installation instructions must always be observed. However, the respective installation instructions do not release the executing company from the obligation to clarify in advance the possible uses and applications of our products, also in connection with the other materials and products used, on the individual project. RoofTech GmbH and the manufacturers of our products assume no responsibility and liability for assembly, suitability and applications.
We assume no liability for errors on our website and in our documents. Pictures and drawings in our documents and webpages serve to clarify individual detail designs and are only recommendations. They can represent development stages, which are not available in such a way. The contents, logos, photos and graphics may only be used or passed on after consultation with RoofTech GmbH. The content and works provided on these Web pages are governed by the copyright laws of Germany. Duplication, processing, distribution, or any form of commercialization of such material beyond the scope of the copyright law shall require the prior written consent of its respective author or creator.
The business relationship is subject to German law, excluding the UN Convention on Contracts for the International Sale of Goods (CISG). Our General Terms and Conditions of Business (GTC) apply, which we will be happy to provide you with at any time (direct link to our RoofTech GTC). The linking of external websites to the RoofTech website is only permitted with the consent of RoofTech GmbH and if no rights of RoofTech GmbH are violated.
No liability for printing errors. Technical changes subject to modification. © 3/2020 Copyright RoofTech GmbH. All rights reserved.